This is an attachment for the Chain Monster robot and it accomplished three missions that are all push and deliver. It technically is not used for the M09 dinosaur toy, but this is because the toy is on the robot while the attachment is below the robot
Third version of a reusable gear attachment. In this scenario a single motor could power two different axles in two different directions. If you use it to accomplish a mission do not forget to send us a video. We would love to see it.
This 3D building instruction is about a FIRST LEGO League 2020 mission called the Slide mission. To accomplish the mission the LEGO Robot must take two LEGO minifigures from a slide and bring them back to base. The whole attachment is built only with parts from LEGO Mindstrorms Robot Inventor Set.
These are instructions on how to build the:
You can find more building instructions and tips and tricks about the competition on this page.
These are instructions on how to build the:
You can find more building instructions and tips and tricks about the competition on this page.
These are instructions on how to build the:
You can find more building instructions and tips and tricks about the competition on this page.
These are instructions on how to build the:
You can find more building instructions and tips and tricks about the competition on this page.
This is a LEGO Education SPIKE Prime robot attachment for accomplishing the FIRST LEGO League 2020 Replay Precision mission . The attachment is designed for Gazon, LEGO Education SPIKE Prime competition robot.
This is a LEGO Education SPIKE Prime robot attachment for accomplishing the FIRST LEGO League 2020 Replay Treadmill mission . The attachment is designed for Gazon, LEGO Education SPIKE Prime competition robot.
Bowling pins mission model reworked from a LEGO Mindstorms EV3 version available at Bowling pins mission models. FLLCasts Off-season Challenge 2019 to a LEGO Education SPIKE Prime version available in this material. You can follow the same construction to assemble as many pins as you need. In 3D building instructions for you to construct them.
Yes, this is a single part. The whole instruction is a single part. This is not an error. This is the part that we use to demonstrate a flip attachment. For consistency even though it is a single LEGO Education SPIKE Prime part, we show the part visually, we don't just mention it in the comments.
Zatty is the smaller sibling if Zat. Zatty is small and cute. It's a car on a frame with 4 small wheels and of course two mini figures riding in it or on it. Built from LEGO SPIKE Core set 45678 + LEGO SPIKE Expansion Set 45680 it was designed by my 7 years old daughter and then slightly improved by me and the colleagues.
Play time for a week: About an hour
This robot is designed to easily lift a cup while still holding it upright. With its motor attached to the side of the hub, the robot can lift the cup to any angle you want. You could replace the LEGO cup and make it lift real cups with a few adjustments. Be careful around liquids though, the robot doesn't like beverages like you do!
These are instructions on how to build the:
You can find more building instructions and tips and tricks about the competition on this page.
These are instructions on how to build the:
You can find more building instructions and tips and tricks about the competition on this page.
This module is made to look and move like a real ship's sails! The module consists of two masts that are connected so that they move together. The back mast is connected to a medium motor that can move all sails and is also connected to a gyro sensor, that can detect if the whole ship is rotated. This module is used in Yolanda - LEGO Mindstorms EV3 Sailship robot.
This module is made to look like a head of a ram made with LEGO Mindstorms EV3. It uses an ultrasonic sensor, which points down as if it is going to attack, as the eyes of the head. It can be combined with other modules to create the perfect ram robot!
These are instructions on how to build the:
for the FIRST LEGO League 2019-2020 City Shaper Challenge.
You can find more building instructions and tips and tricks about the competition on this page.
We want students to be able to easily find the parts and to put the parts back in the designated compartments.
Files are printed on both sides of 160-gram sheet of paper A3 format.
The sorting sheet is designed to fit in the cover of the box. To gather in the lid, the excess parts of the printed sheet must be cut off the markers on the front of the sheet.
To extend the life of the sheets, you can laminate them either with a "laminate matte" or a simple laminate. The disadvantage of the simple laminate is that there is a lot of gloss. The disadvantage of laminate matte is that it has to be sealed with a clear PVA C-200 adhesive to prevent it from opening over time.
We recommend printing doublesided and turning over the "short edge", like a book. If you decide, you may flip the printed result over the long side. Both options are available at you local print center.
