Building Instructions -

• EV3-G

This is the Coffee Pot, along with a coffee mug. It was 2 hours of fun

You know those constructions that you need to push or pull something and you get a cool chain reaction, right? Here are the building instructions of such a Chain Reaction built with LEGO Mindstorms 51515 Robot Inventor set. This construction was created to be used with the smallest Inventor robot Tricky and its Kick the ball attachment. The goal is to program the robot to kick the Mindstorms/Duplo ball, included in the set, so that the ball could push the lever and start the chain reaction.

You can find the LEGO set, with which this was built, by following this link.

You can find constructions created to play with Tricky, by following the links below:

1. Bowling Pins
2. Football Goal
3. Basketball hoop

This robot is named after the South Pole–Aitken Basin, the largest impact crater in the Solar System, located on the far side of the Moon.

Astronauts, get ready to enter lunar orbit! This robot is equipped with a holder for a camera or phone, allowing it to take a picture of the far side of the Moon. If your device does not fit, you can easily adjust the holder to suit your needs.

With its two motors, Aitken can move in both wide and narrow circles around the Moon to capture the perfect photo.

These are instructions on how to build the:

• Colored health units
• Season tiles

You can find more building instructions and tips and tricks about the competition on this page.

These are instructions on how to build the:

• Heavy Tire Flip

You can find more building instructions and tips and tricks about the competition on this page.

This was an idea. You would we demonstration a multi-axle power and rotation transmitting box. Well, here it is. Build it. Start it. And see how the power from the motor is transmitted through different axles. The lever will demonstrate it.

Step by step guide on how to add the SD card to the Raspberry pi. 

The Raspberry Pi must not be powered.  

3D scheme on how to connect the L298N Motor Driver to the Batteries. Follow the step-by-step instructions. Be careful about the PCB terminal connectors.

3D scheme with instructions on how to connect the L298N driver to the batteries and to the motor. Just that. Connecting to the Raspberry Pi is at a later stage of the course. 

These are 3D building instructions on how to connect a diode directly to the batteries and turn it on. 

In Robopartans classes we needed a few parts the the robot could lift in a competition. These is a box that is suitable for this

Shows the pipe attachment constructions that is mounted on the robot. The pipe is than mounted on this constuctions

This is an attachment for Kufar - Easy SPIKE Prime out-of-box robot. It solves M10 Sound Mixer using a passive attachment and collects Noah, the sound engineer using an inertial attachment.

A FIRST LEGO League 2023-2024 attachment for the MiniBox Robot.

This attachment is designed to detach, once it completes its purpose. Due to the way, the attachment is left on the mission model, it slides from, creating distance between itself and the mission model, therefore meeting the requirement that no attachment should be touching the mission model at the end of the competition. This is done, so that the team loses less time switching attachments in the base, lowering the chance of human error during the competition.

This construction is ment as a addition to the base line following robot with exposed sensor.

A FIRST LEGO League 2023-2024 attachment for the MiniBox Robot.

This attachment is designed to detach, once it completes its purpose. This is done, so that the team loses less time switching attachments in the base, lowering the chance of human error during the competition.

This is an alternative model for the FIRST LEGO League 2022-2023 SUPERPOWERED built only with LEGO Education SPIKE Prime parts. The goal of the model is to be able to experiment and learn without the need to have the real parts, that at this moment are almost impossible to find and gather.

This is an alternative mission model for FIRST LEGO League 2022-2023 SUPERPOWERED Hybrid Car mission model. It is alternative as you only need LEGO Education SPIKE Prime parts to build it and you don't need the real parts from the real competition

This is an alternative model for the FIRST LEGO League 2022-2023 SUPERPOWERED build only with LEGO Education SPIKE Prime parts. The goal of the model is to be able to experiment and learn without the need to have the real parts, that at this moment are almost impossible to find and gather.